在郑州区域为什么推荐隔墙板(内含英文翻译)
轻质隔墙板的制造工艺，决定了良好的隔热保温功能，让您的室内环境更加舒适。在郑州区域为什么推荐隔墙板(内含英文翻译)
施工要点：1、检查隔墙板的几何尺寸，以符合标准要求为准。2、根据排图，预先40×50×90L型铁件固定在应固定的部位。3、按排图，从一侧开始安装。若隔墙板上有门窗洞口，就从门窗洞口向两侧开始安装。对准墨线，用撬棍尽力在底部撬动，上端顶紧，板边严实，底部用木楔塞牢，加上加固件。4、安装时，随时检查平整度、垂直度等有关检查的项目。5、水电埋管铺设应与隔墙板安装同步进行，隔墙板面需要开口时，应在安装前钻孔，洞口不得大于80mm×80mm；水暖吊挂件不能超过80公斤，超过80公斤的吊挂件，必须安装在隔墙板的固定预埋件上。6、电器接线开关、插座等四周，应用充填料抹平。7、隔墙板安装后，粘接材料必须干燥，才能进行下道工序，正常需要安装之日起10-15天方能进行装饰。8、安装好的隔墙板面不得起皮、掉角、空鼓和裂缝，按每面墙的平面计算，达到建筑中级抹灰。
轻质隔墙板是一种新型节能墙材料，它是一种外型像空心楼板一样的墙材，但是它两边有公母榫槽，安装时只需将板材立起，公、母隼涂上少量嵌缝砂浆后对拼装起来即可。它是由无害化磷石膏、轻质钢渣、粉煤灰等多种工业废渣组成，经变频蒸汽加压养护而成。轻质隔墙板具有质量轻、强度高、多重环保、保温隔热、隔音、呼吸调湿、防火、快速施工、降低墙体成本等优点。内层装有合理布局的隔热、吸声的无机发泡型材或其他保温材料，墙板经流水线浇注、整平、科学养护而成，生产自动化程度高，规格品种多。
关于更多轻质隔墙板相关资料联系：15515532955（微信同号）
The manufacturing process of light partition board determines the good heat insulation function, making your indoor environment more comfortable.
Key points of Construction: 1. Check the geometric dimension of partition board to meet the standard requirements. 2. According to the layout, 40 in advance × fifty × 90L type iron parts are fixed at the parts that should be fixed. 3. Install from one side according to the layout. If there are door and window openings on the partition board, install from the door and window openings to both sides. Align the ink line, use a crowbar to pry at the bottom as much as possible, tighten the upper end, keep the board edge tight, plug the bottom with a wooden wedge, and add reinforcement. 4. During installation, check the flatness, verticality and other related inspection items at any time. 5. The laying of buried water and electricity pipes should be carried out synchronously with the installation of partition board. When the partition board needs to be opened, it should be drilled before installation, and the opening should not be greater than 80mm × 80mm； Plumbing hangers shall not exceed 80 kg. Hangers exceeding 80 kg must be installed on fixed embedded parts of partition board. 6. The surrounding of electrical wiring switches and sockets shall be smoothed with fillers. 7. After the partition board is installed, the bonding material must be dry before the next process can be carried out. The decoration can be carried out 10-15 days from the date of normal installation. 8. The installed partition board shall be free of peeling, corner falling, hollowing and cracks. It shall be calculated according to the plane of each wall to achieve building intermediate plastering.
Light partition board is a new type of energy-saving wall material. It is a kind of wall material with the same appearance as hollow floor slab, but it has male and female mortise grooves on both sides. When installing, you only need to erect the board, and the male and female falcons can be assembled after being coated with a small amount of caulking mortar. It is composed of harmless phosphogypsum, light steel slag, fly ash and other industrial waste residues, which are cured by variable-frequency steam pressure. Light partition board has the advantages of light weight, high strength, multiple environmental protection, thermal insulation, sound insulation, respiratory humidity regulation, fire prevention, rapid construction, reducing wall cost and so on. The inner layer is equipped with reasonably arranged insulating and sound-absorbing inorganic foaming profiles or other insulation materials. The wallboard is poured, leveled and scientifically maintained by the assembly line. The production automation is high, and there are many specifications and varieties.
For more information about lightweight partition board, contact: 15515532955 (wechat same number)
